♦ Built-in MPPT PV controller
♦1+2+1 radiator fan module
♦Hidden processing design of PV input port and AC input/output port --Pay more attention to safety
♦The design of dual chip cooperative control--The fifth generation circuit design: Inverter control circuit and MPPT solar control circuit
♦The design of circuit board resistant to poor environment--The control circuit is treated by special three proofing coating
♦New generation of ring transformer which is energy-saving and high-efficiency
Normal mode
Normal output
Eco mode
The output voltage is reduced by 20V to save energy under the precondition that the final output voltage of the machine is normal. This mode is mainly applicable to road lighting and indoor/outdoor lighting.
Power-saving mode
When the load is above 200W, the machine remains normal output. When the load is below 150W, the machine stops the output and, after 1 minute, starts the output; when the machine again detects that the load is below 150W, it stops the output (i.e., cyclic output). This mode is mainly applicable to refrigerator and air conditioner.
A complete solar energy system is composed of off-grid solar inverter, solar controller, photovoltaic panel, battery and other parts.Photovoltaic panels to convert solar energy into electricity, battery used for photovoltaic panels into direct current (dc) are stored by the solar photovoltaic controller control threatening the battery and battery for solar power supply, inverter load to battery charging protection, over discharge protection effect, off-grid solar inverter is responsible for direct current (dc) to alternating current.
A conventional inverter requires an additional photovoltaic controller of appropriate capacity between the photovoltaic module and the battery.
Hybrid Inverter with Charger and MPPT Solar charge controller system is a set of battery charging and discharging control,PV array absorption of solar radiation and translate into electrical energy to provide power for the entire system, PV controller and Grid charger achieves the intelligent battery-charging control. The inverter inverts the DC to AC for the load power supplying; and automatic control the start-stop of Grid charger if needed.
The inverter with MPPT controller is an upgraded version of the conventional inverter.It is equipped with the functions of inverter and photovoltaic controller. Generally used in solar power generation systems, it only needs to connect photovoltaic modules and batteries, which can reduce the packaging and transportation costs of external photovoltaic controllers, facilitate installation and save space.
■Important computer systems in securities exchanges, bank, hospitals, etc.;
■ Fire protection, lighting, monitoring and other systems in buildings;
■ Transportation systems covering lighting systems in expressways, tunnels, metros, airports, etc.;
■ Production, experimental and other equipment which must not be powered off;
■ Household electrical appliances.
Type(unit) | SuninvM MPPT 2K 24V |
SuninvM MPPT 3K 24V |
SuninvM MPPT 4K 24V |
SuninvM MPPT 5K 48V |
SuninvM MPPT 6K 48V |
|
Rated capacity(KVA) | 2 | 3 | 4 | 5 | 6 | |
Rated power | 2000W | 3000W | 4000W | 5000W | 6000W | |
MPPT Inverter | 24V/48V 30A | |||||
MPPT voltage input range | MPPT: 50 - 150V | |||||
Grid Input | Voltage range(Vac) | AC165-275V AC85-135V | ||||
Frequency(Hz) | 50Hz | 60Hz | 60Hz | 60Hz | 60Hz | |
Rated charge current(A) | MAX. 30A | |||||
Output | Rated output voltage(V) | 110/115/120V 220/230/240V | ||||
Rated output frequency(Hz) | 50/60±1% | |||||
Output power factor | ≥0.8 | |||||
THD | <3% | |||||
Output wave | Sine wave | |||||
Output phase | Single phase | |||||
Peak factor | 3:1 | |||||
Barrtery | Species | Optional | ||||
Battery rated voltage(V) | DC24 | DC24 | DC24 | DC48 | DC48 | |
Recharging current | 0-30A(Optional) | |||||
Others | Efficiency | ≥85% | ||||
Dynamic response | 5%(load from 0 to 100%) | |||||
Noise level | ≥40dB (1m distance) | |||||
Display interface | Digital display | |||||
Communication interface | USB | |||||
Environmental Temperature(℃) | -30+55 | |||||
Environmental Humidity | 10%-90%(non condensing) | |||||
Protection level | IP21 | |||||
Protection function | Array/ Over voltage/ Over current/ Short circuit/ Reverse connection ect protection function | |||||
Altitude(m) | ≤2000(above 1000m need according GB/T 3859.2 to derate operating) | |||||
Dimensions(mm) | 560x360x260 | 560x360x260 | 560x360x260 | 560x360x260 | 560x360x260 | |
Weight (kg) | 22.5 | 27 | 27.5 | 32.5 | 32.5 |
This inverter is completely beyond my imagination. Its conversion efficiency is very high. After inverter, the AC power output by the inverter is of high quality and good stability, which perfectly meets all my requirements for inverter.
Dealer Feedback
Package & Shipping
Batteries have high requirements for transportation.
For questions about sea transportation, air transportation and road transportation, please consult us.
Multifit Office-Our Company
HQ located in Beijing, China and founded in 2009 Our factory located in 3/F,JieSi Bldg.,6 Keji West Road,Hi-Tech Zone,Shantou,Guangdong,China.
Beijing Multifit Electrical Technology Co.. Ltd. is a high-tech plant for the solar power and renewable energy reseach, production, sales and construction of photovoltaic power station. We are located in the Chinese capital, the center of the Beijing Economic and Technological Development Zone areas-a beautiful high-tech Frtune of 500 companies Industry park.
Dixere certis. Uno praebebat. Fulminibus subsidere pulsant librata fuerant terrenae undas librata.
Homini locavit fluminaque calidis metusque. Fuit haec madescit
vmaxapower brand products, worthy of my trust
I am willing to be a new partner
Customer feedback is very good product
We are long-term partners
Pleasant cooperation
Long-term business
quality assurance
We will do better
smiling service
Do things with integrity
Photovoltaic leader
One-stop service
Brand export to the world
Domestic and foreign exhibitions hot-selling brand